White SPECTRA ceiling light switched off in a pale hallway

The same white SPECTRA ceiling light switched on, with a warm ring and a soft pool on the ceiling

On / off

Aluminium + integrated LED

Five finishes,
one aimed beam.

Already fitted with an LED, the flat disc turns and tilts through 360° and leaves a warm 3000K ring on the wall or the ceiling.

5 aluminium finishes 7W · 230 lm 360° aim IP65 wall or ceiling

Finish

Details worth keeping

A small lamp with a precise job.

You do not add a bulb later. The whole fitting is just the head, the neck, and the canopy.

Close view of the SPECTRA pivot between the disc head and the canopy

Joint

Then tilt it with turn it

360° of rotate-and-tilt lives in the short neck, so the disc can point at a wall, a picture, or down a hall.

Canopy

Then it stays with two screws

The same fitting works on the wall or the ceiling. A shallow round plate is what fixes it.

Light ring

Held at the edge with warm light

The room is not washed out by a flood. What stays at the edge is a shaped accent.

Shaped light

The picture is the light.

Everyday interiors, four finishes, a light-filled study at one end and a quiet bedroom at the other.

White disc ceiling light casting fine lines across a hallway ceiling

White light in the hallway

Overhead in the hallway, a white disc lays fine lines of light into a distinct pattern.

Sage disc ceiling light above a desk in a sunlit study

Sage in the study

Oak furniture, books, and greenery in a sunlit study are a natural setting for the sage finish.

Orange disc ceiling light in a bright living room

Orange in the living room

Pale walls and soft furnishings get a bright colour accent from this orange disc.

Black disc ceiling light in a neutral bedroom

Black in the bedroom

Against warm neutral walls and soft bedding, black stays a quiet contrast.

Lamp and line

The disc stays in the picture.

The warm line is aimed, not floating free. As the head turns, that edge travels the wall, the ceiling, then back toward the lamp.

The lamp The line

The lampThe compact disc keeps a clear, simple silhouette on the ceiling.

The lineA narrow beam draws a defined line across the ceiling and wall.

TogetherRotate and tilt the head to change the direction of the light.

360° aim

Light that shapes a surface.

Want the pool somewhere else? Rotate the head. Ceiling, wall, or the corner between them all work. Orange and tilted up, the warm light lands above the table.

Rotate and tilt through 360°

The same plate mounts on a wall or a ceiling

A shaped 3000K accent, not a whole-room wash

Keep sleeves and doors off the sealed housing.

Orange SPECTRA wall light tilted upward, washing a warm pool onto the ceiling

From the fitting to the switch

One light. Four things to know.

The compact design, the built-in LED, wall-switch control, and installation are what to explore.

Light

A separate bulb is neither supplied nor needed. The LED is already there, at 7W.

Details

Five aluminium finishes, one build: a flat disc, a short neck, and a two-screw canopy at ∅ 4.6″ × 6.4″, or 11.8 cm × 16.3 cm.

Controls

The trailing-edge TRIAC driver is separate and not included. As supplied, this is not dimmable. On and off stay with an ordinary wall switch.

Place it

Ready to install indoors or out, on the wall or the ceiling. The IP65 rating is dust-tight protection against water jets.

Specifications

Kept exact with the numbers.

Every finish keeps one size, one 7W light engine, and one IP65 rating.

Type

Ceiling and wall light

Size

∅ 4.6″ × H 6.4″ / Dia 11.8 cm × H 16.3 cm

Head depth

2.0″ / 5.0 cm

Base

∅ 4.3″ / Dia 11.0 cm

Material

Aluminium

Finish

Black · White · Sage · Terracotta · Orange

Light

Integrated LED 7W

Input

100–240V

Rating

IP65 · wall or ceiling · 360° rotate and tilt

Monulo · The practical guide

Lighting that fits.
A room that feels right.

Find a starting size, see where to place it, and know what to check before installation.

Find your starting size

01 · Get the scale right

A useful starting point, in seconds.

For a central ceiling light, enter your room dimensions. For lights above furniture, use the table or island guide below instead.

Measure first, then mock up the actual shape. Suggested dimensions are design starting points; product instructions and applicable local requirements take priority.

02 · Look up

Work with your ceiling.

The available drop matters as much as the fixture diameter.

Around 8 ft / 2.44 m

Keep it close

Start with a flush or compact semi-flush design in walking areas. Check the complete installed height.

Around 9–10 ft / 2.74–3.05 m

Balance the drop

Pendants become easier to accommodate. Reserve enough clearance below the lowest part of the fitting.

Above 10 ft / 3.05 m

Scale with intention

Test larger forms or longer suspension. Confirm cable length, access for maintenance and ceiling support.

Sloped ceiling? Compatibility is model-specific. Confirm the canopy, suspension angle and required drop before ordering.

30–36 in / 76–91 cm above the tabletop

Room study 01

Dining table

Let the furniture define the focal point.

Measure: Measure the tabletop, including its width at the widest point.
Size & place: For a round fixture, test a diameter around ½–⅔ of the table width. For a linear design, start with ½–⅔ of its length.
Check: Center on the table and check the view across it while seated.

30–36 in / 76–91 cm above the counter

Room study 02

Kitchen island

Plan the whole row before choosing the quantity.

Measure: Record counter length, width and the working area below.
Size & place: Try two or three paper shade outlines. Adjust their widths until adjacent edges and both island ends have breathing room.
Check: Mark equal centers; verify the actual gap between shades rather than using center spacing alone.

Start with at least 7 ft / 213 cm walking clearance

Room study 03

Room center

Use the room formula as a visual starting point.

Measure: Record length, width and finished ceiling height.
Size & place: Add length and width in feet; use that total as a starting diameter in inches. Example: 12 + 14 → 26 in / 66 cm.
Check: Check the furniture plan and the fixture’s visual weight. This formula does not determine brightness.

Keep doors, stairs and walking routes unobstructed

Room study 04

Hallway & entry

A consistent rhythm works better than a crowded ceiling.

Measure: Mark the full walking route, doors and changes in ceiling height.
Size & place: Divide the usable corridor into equal bays. Place each light near a bay center, leaving half a bay at each end.
Check: Choose the final distance from the fixture’s light output and beam spread; test the layout after dark.

Position paired lights symmetrically beside the mirror

Room study 05

Bathroom vanity

Put comfortable facial lighting first.

Measure: Record mirror dimensions, side wall space and cabinet swing.
Size & place: For side sconces, trial the luminous center around 65–70 in / 165–178 cm above the floor.
Check: Adjust to the actual user and mirror. Check for bright reflections and confirm the correct location rating.

Use an adjustable mock-up before fixing wall lights

Room study 06

Bedroom & bedside

Choose the height from where you actually sit.

Measure: Measure the mattress, nightstand and your seated position.
Size & place: Try the shade at seated eye or shoulder height so the bright source is screened and the page is lit.
Check: Check reach to the switch, head movement, pillows and any adjustable arm.

A deeper or diffused shade can improve comfort

Room study 07

Reading & living

Light the page without exposing the source.

Measure: Sit in your usual chair with a book before locating the lamp.
Size & place: Place task lighting beside or slightly behind the shoulder. Add separate ambient lighting to soften contrast.
Check: Keep the base and cord out of traffic; check glare from both the chair and nearby seats.

03 · Before the tools come out

One installation checklist.

Bring the product instructions, room measurements and fixture weight to your installer.

01 / Fit

Mock up the final position

Check door swings, seated views, shade gaps and the lowest point. Include the canopy and suspension in every drop measurement.

02 / Support

Verify the mounting

Have a qualified installer confirm the box, fixing points and structural support for the complete fixture weight.

03 / Compatibility

Match the electrical details

Confirm supply voltage, lamp or LED driver, dimmer compatibility, ceiling type and location rating for the exact model.

Hardwired fixtures should be installed by a qualified electrician following the supplied instructions and local requirements. This page explains planning and placement; it does not provide wiring instructions.

04 · The last few details

Questions before you choose.

Which measurement should I use for the drop?

Measure vertically from the finished ceiling to the lowest point of the assembled fitting. Over a table or counter, measure the remaining gap from that point to the surface.

Does a larger light always mean a brighter room?

No. Diameter describes the physical size. Compare lumen output, shade opacity, beam direction and the room’s other light sources separately.

How do I choose between two or three island pendants?

Start with the shade diameter, then draw the complete row to scale. Two larger shades and three small shades can both work; use actual edge gaps and counter-end clearances to decide.

What if my ceiling is too low for the light I like?

Compare a shorter suspension or a flush alternative that the manufacturer supports. Never shorten a rigid stem or modify wiring without the appropriate product guidance.

Can any fixture go in a bathroom or on a sloped ceiling?

No. Check the exact product specification and installation position. Ask a qualified installer to confirm the required damp or wet rating and canopy compatibility.

What should I send when asking for sizing advice?

Include a room photo, ceiling height, room or furniture dimensions, the fixture link and your proposed installation location. For heavier fittings, include any available mounting information.

Language

Sign in

Reset your password

Tilting Head Round Disc Aluminium Wall Light

12% OFF

15% OFF

18% OFF

$60 OFF

$100 OFF

Question

Shipping info

Five finishes,one aimed beam.

A small lamp with a precise job.

Then tilt it with turn it

Then it stays with two screws

Held at the edge with warm light

The picture is the light.

White light in the hallway

Sage in the study

Orange in the living room

Black in the bedroom

The disc stays in the picture.

Light that shapes a surface.

One light. Four things to know.

Light

Details

Controls

Place it

Kept exact with the numbers.

Customer Reviews

Lighting that fits.A room that feels right.

A useful starting point, in seconds.

Work with your ceiling.

Keep it close

Balance the drop

Scale with intention

Dining table

Kitchen island

Room center

Hallway & entry

Bathroom vanity

Bedroom & bedside

Reading & living

One installation checklist.

Mock up the final position

Verify the mounting

Match the electrical details

Questions before you choose.

A little measuring. A better fit.

You May Also Like

Five finishes,
one aimed beam.

Lighting that fits.
A room that feels right.